/* WiFi Web Server A simple web server that shows the value of the analog input pins. using a WiFi shield. This example is written to configure the WiFi settings using provisioning mode. It also sets up an mDNS server so the IP address of the board doesn't have to be obtained via the serial monitor. Circuit: WiFi shield attached Analog inputs attached to pins A0 through A5 (optional) created 13 July 2010 by dlf (Metodo2 srl) modified 31 May 2012 by Tom Igoe */ #include #include #include const int ledPin = 6; // LED pin for connectivity status indicator char mdnsName[] = "wifi101"; // the MDNS name that the board will respond to // after WiFi settings have been provisioned // Note that the actual MDNS name will have '.local' after // the name above, so "wifi101" will be accessible on // the MDNS name "wifi101.local". WiFiServer server(80); // Create a MDNS responder to listen and respond to MDNS name requests. WiFiMDNSResponder mdnsResponder; void setup() { //Initialize serial: Serial.begin(9600); // check for the presence of the shield: if (WiFi.status() == WL_NO_SHIELD) { Serial.println("WiFi shield not present"); // don't continue: while (true); } // configure the LED pin for output mode pinMode(ledPin, OUTPUT); // Start in provisioning mode: // 1) This will try to connect to a previously associated access point. // 2) If this fails, an access point named "wifi101-XXXX" will be created, where XXXX // is the last 4 digits of the boards MAC address. Once you are connected to the access point, // you can configure an SSID and password by visiting http://wifi101/ WiFi.beginProvision(); while (WiFi.status() != WL_CONNECTED) { // wait while not connected // blink the led to show an unconnected status digitalWrite(ledPin, HIGH); delay(500); digitalWrite(ledPin, LOW); delay(500); } // connected, make the LED stay on digitalWrite(ledPin, HIGH); server.begin(); // Setup the MDNS responder to listen to the configured name. // NOTE: You _must_ call this _after_ connecting to the WiFi network and // being assigned an IP address. if (!mdnsResponder.begin(mdnsName)) { Serial.println("Failed to start MDNS responder!"); while(1); } Serial.print("Server listening at http://"); Serial.print(mdnsName); Serial.println(".local/"); // you're connected now, so print out the status: printWiFiStatus(); } void loop() { // Call the update() function on the MDNS responder every loop iteration to // make sure it can detect and respond to name requests. mdnsResponder.poll(); // listen for incoming clients WiFiClient client = server.available(); if (client) { Serial.println("new client"); // an http request ends with a blank line boolean currentLineIsBlank = true; while (client.connected()) { if (client.available()) { char c = client.read(); Serial.write(c); // if you've gotten to the end of the line (received a newline // character) and the line is blank, the http request has ended, // so you can send a reply if (c == '\n' && currentLineIsBlank) { // send a standard http response header client.println("HTTP/1.1 200 OK"); client.println("Content-Type: text/html"); client.println("Connection: close"); // the connection will be closed after completion of the response client.println("Refresh: 5"); // refresh the page automatically every 5 sec client.println(); client.println(""); client.println(""); // output the value of each analog input pin for (int analogChannel = 0; analogChannel < 6; analogChannel++) { int sensorReading = analogRead(analogChannel); client.print("analog input "); client.print(analogChannel); client.print(" is "); client.print(sensorReading); client.println("
"); } client.println(""); break; } if (c == '\n') { // you're starting a new line currentLineIsBlank = true; } else if (c != '\r') { // you've gotten a character on the current line currentLineIsBlank = false; } } } // give the web browser time to receive the data delay(1); // close the connection: client.stop(); Serial.println("client disonnected"); } } void printWiFiStatus() { // print the SSID of the network you're attached to: Serial.print("SSID: "); Serial.println(WiFi.SSID()); // print your WiFi shield's IP address: IPAddress ip = WiFi.localIP(); Serial.print("IP Address: "); Serial.println(ip); // print the received signal strength: long rssi = WiFi.RSSI(); Serial.print("signal strength (RSSI):"); Serial.print(rssi); Serial.println(" dBm"); }