143 lines
4.3 KiB
Arduino
143 lines
4.3 KiB
Arduino
|
/*
|
||
|
WiFiEsp example: WebServerLed
|
||
|
|
||
|
A simple web server that lets you turn on and of an LED via a web page.
|
||
|
This sketch will print the IP address of your ESP8266 module (once connected)
|
||
|
to the Serial monitor. From there, you can open that address in a web browser
|
||
|
to turn on and off the LED on pin 13.
|
||
|
|
||
|
For more details see: http://yaab-arduino.blogspot.com/p/wifiesp.html
|
||
|
*/
|
||
|
|
||
|
#include "WiFiEsp.h"
|
||
|
|
||
|
// Emulate Serial1 on pins 6/7 if not present
|
||
|
#ifndef HAVE_HWSERIAL1
|
||
|
#include "SoftwareSerial.h"
|
||
|
SoftwareSerial Serial1(6, 7); // RX, TX
|
||
|
#endif
|
||
|
|
||
|
char ssid[] = "Twim"; // your network SSID (name)
|
||
|
char pass[] = "12345678"; // your network password
|
||
|
int status = WL_IDLE_STATUS;
|
||
|
|
||
|
int ledStatus = LOW;
|
||
|
|
||
|
WiFiEspServer server(80);
|
||
|
|
||
|
// use a ring buffer to increase speed and reduce memory allocation
|
||
|
RingBuffer buf(8);
|
||
|
|
||
|
void setup()
|
||
|
{
|
||
|
pinMode(LED_BUILTIN, OUTPUT); // initialize digital pin LED_BUILTIN as an output.
|
||
|
Serial.begin(115200); // initialize serial for debugging
|
||
|
Serial1.begin(9600); // initialize serial for ESP module
|
||
|
WiFi.init(&Serial1); // initialize ESP module
|
||
|
|
||
|
// check for the presence of the shield
|
||
|
if (WiFi.status() == WL_NO_SHIELD) {
|
||
|
Serial.println("WiFi shield not present");
|
||
|
// don't continue
|
||
|
while (true);
|
||
|
}
|
||
|
|
||
|
// attempt to connect to WiFi network
|
||
|
while (status != WL_CONNECTED) {
|
||
|
Serial.print("Attempting to connect to WPA SSID: ");
|
||
|
Serial.println(ssid);
|
||
|
// Connect to WPA/WPA2 network
|
||
|
status = WiFi.begin(ssid, pass);
|
||
|
}
|
||
|
|
||
|
Serial.println("You're connected to the network");
|
||
|
printWifiStatus();
|
||
|
|
||
|
// start the web server on port 80
|
||
|
server.begin();
|
||
|
}
|
||
|
|
||
|
|
||
|
void loop()
|
||
|
{
|
||
|
WiFiEspClient client = server.available(); // listen for incoming clients
|
||
|
|
||
|
if (client) { // if you get a client,
|
||
|
Serial.println("New client"); // print a message out the serial port
|
||
|
buf.init(); // initialize the circular buffer
|
||
|
while (client.connected()) { // loop while the client's connected
|
||
|
if (client.available()) { // if there's bytes to read from the client,
|
||
|
char c = client.read(); // read a byte, then
|
||
|
buf.push(c); // push it to the ring buffer
|
||
|
|
||
|
// printing the stream to the serial monitor will slow down
|
||
|
// the receiving of data from the ESP filling the serial buffer
|
||
|
//Serial.write(c);
|
||
|
|
||
|
// you got two newline characters in a row
|
||
|
// that's the end of the HTTP request, so send a response
|
||
|
if (buf.endsWith("\r\n\r\n")) {
|
||
|
sendHttpResponse(client);
|
||
|
break;
|
||
|
}
|
||
|
|
||
|
// Check to see if the client request was "GET /H" or "GET /L":
|
||
|
if (buf.endsWith("GET /H")) {
|
||
|
Serial.println("Turn led ON");
|
||
|
ledStatus = HIGH;
|
||
|
digitalWrite(LED_BUILTIN, HIGH); // turn the LED on (HIGH is the voltage level)
|
||
|
}
|
||
|
else if (buf.endsWith("GET /L")) {
|
||
|
Serial.println("Turn led OFF");
|
||
|
ledStatus = LOW;
|
||
|
digitalWrite(LED_BUILTIN, LOW); // turn the LED off by making the voltage LOW
|
||
|
}
|
||
|
}
|
||
|
}
|
||
|
|
||
|
// close the connection
|
||
|
client.stop();
|
||
|
Serial.println("Client disconnected");
|
||
|
}
|
||
|
}
|
||
|
|
||
|
|
||
|
void sendHttpResponse(WiFiEspClient client)
|
||
|
{
|
||
|
// HTTP headers always start with a response code (e.g. HTTP/1.1 200 OK)
|
||
|
// and a content-type so the client knows what's coming, then a blank line:
|
||
|
client.println("HTTP/1.1 200 OK");
|
||
|
client.println("Content-type:text/html");
|
||
|
client.println();
|
||
|
|
||
|
// the content of the HTTP response follows the header:
|
||
|
client.print("The LED is ");
|
||
|
client.print(ledStatus);
|
||
|
client.println("<br>");
|
||
|
client.println("<br>");
|
||
|
|
||
|
client.println("Click <a href=\"/H\">here</a> turn the LED on<br>");
|
||
|
client.println("Click <a href=\"/L\">here</a> turn the LED off<br>");
|
||
|
|
||
|
// The HTTP response ends with another blank line:
|
||
|
client.println();
|
||
|
}
|
||
|
|
||
|
void printWifiStatus()
|
||
|
{
|
||
|
// print the SSID of the network you're attached to
|
||
|
Serial.print("SSID: ");
|
||
|
Serial.println(WiFi.SSID());
|
||
|
|
||
|
// print your WiFi shield's IP address
|
||
|
IPAddress ip = WiFi.localIP();
|
||
|
Serial.print("IP Address: ");
|
||
|
Serial.println(ip);
|
||
|
|
||
|
// print where to go in the browser
|
||
|
Serial.println();
|
||
|
Serial.print("To see this page in action, open a browser to http://");
|
||
|
Serial.println(ip);
|
||
|
Serial.println();
|
||
|
}
|