116 lines
2.7 KiB
Arduino
116 lines
2.7 KiB
Arduino
|
/*
|
||
|
|
|
||
|
|
This example connects to an unencrypted WiFi network.
|
||
|
|
Then it prints the MAC address of the WiFi shield,
|
||
|
|
the IP address obtained, and other network details.
|
||
|
|
|
||
|
|
Circuit:
|
||
|
|
* WiFi shield attached
|
||
|
|
|
||
|
|
created 13 July 2010
|
||
|
|
by dlf (Metodo2 srl)
|
||
|
|
modified 31 May 2012
|
||
|
|
by Tom Igoe
|
||
|
|
*/
|
||
|
|
#include <SPI.h>
|
||
|
|
#include <WiFi101.h>
|
||
|
|
#include "arduino_secrets.h"
|
||
|
|
///////please enter your sensitive data in the Secret tab/arduino_secrets.h
|
||
|
|
char ssid[] = SECRET_SSID; // your network SSID (name)
|
||
|
|
int status = WL_IDLE_STATUS; // the WiFi radio's status
|
||
|
|
|
||
|
|
void setup() {
|
||
|
|
//Initialize serial and wait for port to open:
|
||
|
|
Serial.begin(9600);
|
||
|
|
while (!Serial) {
|
||
|
|
; // wait for serial port to connect. Needed for native USB port only
|
||
|
|
}
|
||
|
|
|
||
|
|
// check for the presence of the shield:
|
||
|
|
if (WiFi.status() == WL_NO_SHIELD) {
|
||
|
|
Serial.println("WiFi shield not present");
|
||
|
|
// don't continue:
|
||
|
|
while (true);
|
||
|
|
}
|
||
|
|
|
||
|
|
// attempt to connect to WiFi network:
|
||
|
|
while ( status != WL_CONNECTED) {
|
||
|
|
Serial.print("Attempting to connect to open SSID: ");
|
||
|
|
Serial.println(ssid);
|
||
|
|
status = WiFi.begin(ssid);
|
||
|
|
|
||
|
|
// wait 10 seconds for connection:
|
||
|
|
delay(10000);
|
||
|
|
}
|
||
|
|
|
||
|
|
// you're connected now, so print out the data:
|
||
|
|
Serial.print("You're connected to the network");
|
||
|
|
printCurrentNet();
|
||
|
|
printWiFiData();
|
||
|
|
}
|
||
|
|
|
||
|
|
void loop() {
|
||
|
|
// check the network connection once every 10 seconds:
|
||
|
|
delay(10000);
|
||
|
|
printCurrentNet();
|
||
|
|
}
|
||
|
|
|
||
|
|
void printWiFiData() {
|
||
|
|
// print your WiFi shield's IP address:
|
||
|
|
IPAddress ip = WiFi.localIP();
|
||
|
|
Serial.print("IP Address: ");
|
||
|
|
Serial.println(ip);
|
||
|
|
Serial.println(ip);
|
||
|
|
|
||
|
|
// print your MAC address:
|
||
|
|
byte mac[6];
|
||
|
|
WiFi.macAddress(mac);
|
||
|
|
Serial.print("MAC address: ");
|
||
|
|
printMacAddress(mac);
|
||
|
|
|
||
|
|
// print your subnet mask:
|
||
|
|
IPAddress subnet = WiFi.subnetMask();
|
||
|
|
Serial.print("NetMask: ");
|
||
|
|
Serial.println(subnet);
|
||
|
|
|
||
|
|
// print your gateway address:
|
||
|
|
IPAddress gateway = WiFi.gatewayIP();
|
||
|
|
Serial.print("Gateway: ");
|
||
|
|
Serial.println(gateway);
|
||
|
|
}
|
||
|
|
|
||
|
|
void printCurrentNet() {
|
||
|
|
// print the SSID of the network you're attached to:
|
||
|
|
Serial.print("SSID: ");
|
||
|
|
Serial.println(WiFi.SSID());
|
||
|
|
|
||
|
|
// print the MAC address of the router you're attached to:
|
||
|
|
byte bssid[6];
|
||
|
|
WiFi.BSSID(bssid);
|
||
|
|
Serial.print("BSSID: ");
|
||
|
|
printMacAddress(bssid);
|
||
|
|
|
||
|
|
// print the received signal strength:
|
||
|
|
long rssi = WiFi.RSSI();
|
||
|
|
Serial.print("signal strength (RSSI):");
|
||
|
|
Serial.println(rssi);
|
||
|
|
|
||
|
|
// print the encryption type:
|
||
|
|
byte encryption = WiFi.encryptionType();
|
||
|
|
Serial.print("Encryption Type:");
|
||
|
|
Serial.println(encryption, HEX);
|
||
|
|
}
|
||
|
|
|
||
|
|
void printMacAddress(byte mac[]) {
|
||
|
|
for (int i = 5; i >= 0; i--) {
|
||
|
|
if (mac[i] < 16) {
|
||
|
|
Serial.print("0");
|
||
|
|
}
|
||
|
|
Serial.print(mac[i], HEX);
|
||
|
|
if (i > 0) {
|
||
|
|
Serial.print(":");
|
||
|
|
}
|
||
|
|
}
|
||
|
|
Serial.println();
|
||
|
|
}
|