97 lines
2.7 KiB
Arduino
97 lines
2.7 KiB
Arduino
|
/*
|
||
|
|
|
||
|
|
Advanced BH1750 library usage example
|
||
|
|
|
||
|
|
This example has some comments about advanced usage features.
|
||
|
|
|
||
|
|
Connection:
|
||
|
|
|
||
|
|
VCC -> 3V3 or 5V
|
||
|
|
GND -> GND
|
||
|
|
SCL -> SCL (A5 on Arduino Uno, Leonardo, etc or 21 on Mega and Due, on esp8266 free selectable)
|
||
|
|
SDA -> SDA (A4 on Arduino Uno, Leonardo, etc or 20 on Mega and Due, on esp8266 free selectable)
|
||
|
|
ADD -> (not connected) or GND
|
||
|
|
|
||
|
|
ADD pin is used to set sensor I2C address. If it has voltage greater or equal to
|
||
|
|
0.7VCC voltage (e.g. you've connected it to VCC) the sensor address will be
|
||
|
|
0x5C. In other case (if ADD voltage less than 0.7 * VCC) the sensor address will
|
||
|
|
be 0x23 (by default).
|
||
|
|
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include <Wire.h>
|
||
|
|
#include <BH1750.h>
|
||
|
|
|
||
|
|
/*
|
||
|
|
|
||
|
|
BH1750 can be physically configured to use two I2C addresses:
|
||
|
|
- 0x23 (most common) (if ADD pin had < 0.7VCC voltage)
|
||
|
|
- 0x5C (if ADD pin had > 0.7VCC voltage)
|
||
|
|
|
||
|
|
Library uses 0x23 address as default, but you can define any other address.
|
||
|
|
If you had troubles with default value - try to change it to 0x5C.
|
||
|
|
|
||
|
|
*/
|
||
|
|
BH1750 lightMeter(0x23);
|
||
|
|
|
||
|
|
void setup(){
|
||
|
|
|
||
|
|
Serial.begin(9600);
|
||
|
|
|
||
|
|
// Initialize the I2C bus (BH1750 library doesn't do this automatically)
|
||
|
|
Wire.begin();
|
||
|
|
// On esp8266 you can select SCL and SDA pins using Wire.begin(D4, D3);
|
||
|
|
|
||
|
|
/*
|
||
|
|
|
||
|
|
BH1750 has six different measurement modes. They are divided in two groups;
|
||
|
|
continuous and one-time measurements. In continuous mode, sensor continuously
|
||
|
|
measures lightness value. In one-time mode the sensor makes only one
|
||
|
|
measurement and then goes into Power Down mode.
|
||
|
|
|
||
|
|
Each mode, has three different precisions:
|
||
|
|
|
||
|
|
- Low Resolution Mode - (4 lx precision, 16ms measurement time)
|
||
|
|
- High Resolution Mode - (1 lx precision, 120ms measurement time)
|
||
|
|
- High Resolution Mode 2 - (0.5 lx precision, 120ms measurement time)
|
||
|
|
|
||
|
|
By default, the library uses Continuous High Resolution Mode, but you can
|
||
|
|
set any other mode, by passing it to BH1750.begin() or BH1750.configure()
|
||
|
|
functions.
|
||
|
|
|
||
|
|
[!] Remember, if you use One-Time mode, your sensor will go to Power Down
|
||
|
|
mode each time, when it completes a measurement and you've read it.
|
||
|
|
|
||
|
|
Full mode list:
|
||
|
|
|
||
|
|
BH1750_CONTINUOUS_LOW_RES_MODE
|
||
|
|
BH1750_CONTINUOUS_HIGH_RES_MODE (default)
|
||
|
|
BH1750_CONTINUOUS_HIGH_RES_MODE_2
|
||
|
|
|
||
|
|
BH1750_ONE_TIME_LOW_RES_MODE
|
||
|
|
BH1750_ONE_TIME_HIGH_RES_MODE
|
||
|
|
BH1750_ONE_TIME_HIGH_RES_MODE_2
|
||
|
|
|
||
|
|
*/
|
||
|
|
|
||
|
|
// begin returns a boolean that can be used to detect setup problems.
|
||
|
|
if (lightMeter.begin(BH1750::CONTINUOUS_HIGH_RES_MODE)) {
|
||
|
|
Serial.println(F("BH1750 Advanced begin"));
|
||
|
|
}
|
||
|
|
else {
|
||
|
|
Serial.println(F("Error initialising BH1750"));
|
||
|
|
}
|
||
|
|
|
||
|
|
}
|
||
|
|
|
||
|
|
|
||
|
|
void loop() {
|
||
|
|
|
||
|
|
uint16_t lux = lightMeter.readLightLevel();
|
||
|
|
Serial.print("Light: ");
|
||
|
|
Serial.print(lux);
|
||
|
|
Serial.println(" lx");
|
||
|
|
delay(1000);
|
||
|
|
|
||
|
|
}
|