76 lines
4.0 KiB
Arduino
76 lines
4.0 KiB
Arduino
|
/*
|
||
|
|
DS250x add-only programmable memory reader w/SKIP ROM.
|
||
|
|
|
||
|
|
The DS250x is a 512/1024bit add-only PROM(you can add data but cannot change the old one) that's used mainly for device identification purposes
|
||
|
|
like serial number, mfgr data, unique identifiers, etc. It uses the Maxim 1-wire bus.
|
||
|
|
|
||
|
|
This sketch will use the SKIP ROM function that skips the 1-Wire search phase since we only have one device connected in the bus on digital pin 6.
|
||
|
|
If more than one device is connected to the bus, it will fail.
|
||
|
|
Sketch will not verify if device connected is from the DS250x family since the skip rom function effectively skips the family-id byte readout.
|
||
|
|
thus it is possible to run this sketch with any Maxim OneWire device in which case the command CRC will most likely fail.
|
||
|
|
Sketch will only read the first page of memory(32bits) starting from the lower address(0000h), if more than 1 device is present, then use the sketch with search functions.
|
||
|
|
Remember to put a 4.7K pullup resistor between pin 6 and +Vcc
|
||
|
|
|
||
|
|
To change the range or ammount of data to read, simply change the data array size, LSB/MSB addresses and for loop iterations
|
||
|
|
|
||
|
|
This example code is in the public domain and is provided AS-IS.
|
||
|
|
|
||
|
|
Built with Arduino 0022 and PJRC OneWire 2.0 library http://www.pjrc.com/teensy/td_libs_OneWire.html
|
||
|
|
|
||
|
|
created by Guillermo Lovato <glovato@gmail.com>
|
||
|
|
march/2011
|
||
|
|
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include <OneWire.h>
|
||
|
|
OneWire ds(6); // OneWire bus on digital pin 6
|
||
|
|
void setup() {
|
||
|
|
Serial.begin (9600);
|
||
|
|
}
|
||
|
|
|
||
|
|
void loop() {
|
||
|
|
byte i; // This is for the for loops
|
||
|
|
boolean present; // device present var
|
||
|
|
byte data[32]; // container for the data from device
|
||
|
|
byte leemem[3] = { // array with the commands to initiate a read, DS250x devices expect 3 bytes to start a read: command,LSB&MSB adresses
|
||
|
|
0xF0 , 0x00 , 0x00 }; // 0xF0 is the Read Data command, followed by 00h 00h as starting address(the beginning, 0000h)
|
||
|
|
byte ccrc; // Variable to store the command CRC
|
||
|
|
byte ccrc_calc;
|
||
|
|
|
||
|
|
present = ds.reset(); // OneWire bus reset, always needed to start operation on the bus, returns a 1/TRUE if there's a device present.
|
||
|
|
ds.skip(); // Skip ROM search
|
||
|
|
|
||
|
|
if (present == true) { // We only try to read the data if there's a device present
|
||
|
|
Serial.println("DS250x device present");
|
||
|
|
ds.write(leemem[0],1); // Read data command, leave ghost power on
|
||
|
|
ds.write(leemem[1],1); // LSB starting address, leave ghost power on
|
||
|
|
ds.write(leemem[2],1); // MSB starting address, leave ghost power on
|
||
|
|
|
||
|
|
ccrc = ds.read(); // DS250x generates a CRC for the command we sent, we assign a read slot and store it's value
|
||
|
|
ccrc_calc = OneWire::crc8(leemem, 3); // We calculate the CRC of the commands we sent using the library function and store it
|
||
|
|
|
||
|
|
if ( ccrc_calc != ccrc) { // Then we compare it to the value the ds250x calculated, if it fails, we print debug messages and abort
|
||
|
|
Serial.println("Invalid command CRC!");
|
||
|
|
Serial.print("Calculated CRC:");
|
||
|
|
Serial.println(ccrc_calc,HEX); // HEX makes it easier to observe and compare
|
||
|
|
Serial.print("DS250x readback CRC:");
|
||
|
|
Serial.println(ccrc,HEX);
|
||
|
|
return; // Since CRC failed, we abort the rest of the loop and start over
|
||
|
|
}
|
||
|
|
Serial.println("Data is: "); // For the printout of the data
|
||
|
|
for ( i = 0; i < 32; i++) { // Now it's time to read the PROM data itself, each page is 32 bytes so we need 32 read commands
|
||
|
|
data[i] = ds.read(); // we store each read byte to a different position in the data array
|
||
|
|
Serial.print(data[i]); // printout in ASCII
|
||
|
|
Serial.print(" "); // blank space
|
||
|
|
}
|
||
|
|
Serial.println();
|
||
|
|
delay(5000); // Delay so we don't saturate the serial output
|
||
|
|
}
|
||
|
|
else { // Nothing is connected in the bus
|
||
|
|
Serial.println("Nothing connected");
|
||
|
|
delay(3000);
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
|