st-anything/lib/WiFiEsp/examples/WebServerAP/WebServerAP.ino

129 lines
3.8 KiB
Arduino
Raw Permalink Normal View History

2023-03-11 14:11:03 +00:00
/*
WiFiEsp example: WebServerAP
A simple web server that shows the value of the analog input
pins via a web page using an ESP8266 module.
This sketch will start an access point and print the IP address of your
ESP8266 module to the Serial monitor. From there, you can open
that address in a web browser to display the web page.
The web page will be automatically refreshed each 20 seconds.
For more details see: http://yaab-arduino.blogspot.com/p/wifiesp.html
*/
#include "WiFiEsp.h"
// Emulate Serial1 on pins 6/7 if not present
#ifndef HAVE_HWSERIAL1
#include "SoftwareSerial.h"
SoftwareSerial Serial1(6, 7); // RX, TX
#endif
char ssid[] = "TwimEsp"; // your network SSID (name)
char pass[] = "12345678"; // your network password
int status = WL_IDLE_STATUS; // the Wifi radio's status
int reqCount = 0; // number of requests received
WiFiEspServer server(80);
// use a ring buffer to increase speed and reduce memory allocation
RingBuffer buf(8);
void setup()
{
Serial.begin(115200); // initialize serial for debugging
Serial1.begin(9600); // initialize serial for ESP module
WiFi.init(&Serial1); // initialize ESP module
// check for the presence of the shield
if (WiFi.status() == WL_NO_SHIELD) {
Serial.println("WiFi shield not present");
while (true); // don't continue
}
Serial.print("Attempting to start AP ");
Serial.println(ssid);
// uncomment these two lines if you want to set the IP address of the AP
//IPAddress localIp(192, 168, 111, 111);
//WiFi.configAP(localIp);
// start access point
status = WiFi.beginAP(ssid, 10, pass, ENC_TYPE_WPA2_PSK);
Serial.println("Access point started");
printWifiStatus();
// start the web server on port 80
server.begin();
Serial.println("Server started");
}
void loop()
{
WiFiEspClient client = server.available(); // listen for incoming clients
if (client) { // if you get a client,
Serial.println("New client"); // print a message out the serial port
buf.init(); // initialize the circular buffer
while (client.connected()) { // loop while the client's connected
if (client.available()) { // if there's bytes to read from the client,
char c = client.read(); // read a byte, then
buf.push(c); // push it to the ring buffer
// you got two newline characters in a row
// that's the end of the HTTP request, so send a response
if (buf.endsWith("\r\n\r\n")) {
sendHttpResponse(client);
break;
}
}
}
// give the web browser time to receive the data
delay(10);
// close the connection
client.stop();
Serial.println("Client disconnected");
}
}
void sendHttpResponse(WiFiEspClient client)
{
client.print(
"HTTP/1.1 200 OK\r\n"
"Content-Type: text/html\r\n"
"Connection: close\r\n" // the connection will be closed after completion of the response
"Refresh: 20\r\n" // refresh the page automatically every 20 sec
"\r\n");
client.print("<!DOCTYPE HTML>\r\n");
client.print("<html>\r\n");
client.print("<h1>Hello World!</h1>\r\n");
client.print("Requests received: ");
client.print(++reqCount);
client.print("<br>\r\n");
client.print("Analog input A0: ");
client.print(analogRead(0));
client.print("<br>\r\n");
client.print("</html>\r\n");
}
void printWifiStatus()
{
// print your WiFi shield's IP address
IPAddress ip = WiFi.localIP();
Serial.print("IP Address: ");
Serial.println(ip);
// print where to go in the browser
Serial.println();
Serial.print("To see this page in action, connect to ");
Serial.print(ssid);
Serial.print(" and open a browser to http://");
Serial.println(ip);
Serial.println();
}